PLUMBING 101: A NECESSITY FOR BATHTUB INSTALLATION

Plumbing 101: A Necessity for Bathtub Installation

Plumbing 101: A Necessity for Bathtub Installation

Blog Article

Call

We have discovered this post about How to Install a Bathtub Yourself directly below on the net and felt it made perfect sense to discuss it with you over here.


How to Install a Bathtub Yourself
Setting up a bath tub isn't specifically rocket science, yet it does require strong plumbing, woodworking, and also occasionally, tiling abilities. Changing an old bathtub with a new one is also a moderately difficult job. If the old tub is easily easily accessible, the task can move speedily; if you have to open up a wall surface to remove the old bathtub as well as position the brand-new bath tub, the job is a lot harder. In either case, the task is within a house handyman's abilities, although you will require a helper to leave the old bathtub and also embeded in the brand-new one. Make certain you have certified yourself for the job as well as are comfortable attempting it. Instead of hiring a contractor to take over a halfway-completed task, it is far better to consider employing one before you start. Chances are you might need a professional plumber to make tube links.
This write-up will assist you set up a new tub in your restroom if you have actually already bought a new tub as well as don't need to transform the plan of your previous supply of water pipelines.
Your tools as well as material list ought to comprise the following:
  • New Bath tub
  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Safety Glasses

  • Level

  • Pliers

  • Adjustable Wrench

  • Putty Blade

  • Screwdriver

  • Cold Knife

  • Tape Measure

  • Pipeline Caps


  • Getting ready for the Installment


    Firstly, the supporting structure supplied with the bathroom ought to be fitted (if called for) according to the producer's directions. Next off, fit the faucets or mixer to the bath tub. When suitable the tap block, it is necessary to make certain that if the tap includes a plastic washer, it is fitted in between the bath and the faucets. On a plastic bathroom, it is also practical to fit a sustaining plate under the faucets system to prevent strain on the tub.
    Fit the versatile tap adapters to the bottom of the two faucets using 2 nuts and olives (occasionally supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet via the hole in the bathroom. Use the nut supplied by the maker to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
    Next, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which should be fitted inside the bathroom. Ensure you utilize all of the supplied washers.
    Attach the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Attach all-time low of the overflow tube in a comparable manner.The bath should now prepare to be suited its last position.

    Removing Old Touches


    If you need to replace old faucets with new ones as a part of your setup, after that the first thing you need to do is detach the water system. After doing so, switch on the faucets to drain any water continuing to be in the system. The procedure of eliminating the existing taps can be fairly problematic because of the limited gain access to that is often the situation.
    Make use of a container wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipes to the faucets. Have a towel prepared for the staying water that will originate from the pipelines. As soon as the supply pipes have been removed, use the very same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly need to quit the single taps from transforming during this procedure. As soon as the faucets have been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any old securing substance.
    Before proceeding to fit the new faucets, compare the pipeline connections on the old faucets to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is required for the new taps to fit.

    Setting up the Bath tub


    Utilizing both wooden boards under its feet, put the tub in the needed position. The wooden boards are handy in uniformly spreading the weight of the tub over the area of the boards rather than focusing all the weight onto four tiny factors.
    The next objective is to make sure that the bathtub is leveled all round. This can be attained by inspecting the level and changing the feet on the bathtub until the spirit level reviews level.
    To install faucets, fit the bottom of the furthest flexible tap port to the suitable supply pipe by making a compression sign up with; then do the very same for the other faucet.
    Turn on the water as well as check all joints and also brand-new pipework for leaks as well as tighten them if essential. Load the bath tub and also examine the overflow electrical outlet and the regular outlet for leaks.
    Finally, fix the bathroom paneling as defined in the supplier's instruction manual. Tiling as well as securing around the tub ought to wait until the bathtub has been utilized at least when as this will certainly settle it into its last setting.

    Suitable New Touches


    If the tails of the new taps are plastic, then you will require a plastic adapter to avoid damage to the string. One end of the port fits on the plastic tail of the faucet and the other end supplies a connection to the existing supply pipes.
    If you require to fit a monobloc, then you will call for lowering couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
    Next, place the tap in the installing opening in the bath/basin making certain that the washers remain in location between the tap as well as the sink. Secure the tap in position with the producer supplied backnut. Once the tap is firmly in place, the supply pipes can be connected to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with typical faucet adapters. The former kind should be connected to the faucet ends first, tightening only by hand. The supply pipelines can later on be connected to the other end. Tighten both ends with a spanner after both ends have actually been linked.

    Tiling Around the Bathtub


    In the area where the bathroom satisfies the floor tile, it is required to secure the accompanies a silicone rubber caulking. This is important as the installation can move enough to crack an inflexible seal, creating the water to penetrate the wall in between the bathroom as well as the tiling, causing issues with moisture and also possible leakages to the ceiling listed below.
    You can choose from a selection of coloured sealers to assimilate your fixtures and fittings. They are offered in tubes and cartridges, and can sealing voids approximately a size of 3mm (1/8 inch). If you have a larger void to load, you can load it with twists of drenched paper or soft rope. Keep in mind to always load the bath tub with water prior to securing, to enable the movement experienced when the tub is in use. The sealer can crack fairly early if you do not take into consideration this activity before sealing.
    Additionally, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are likewise quickly readily available on the market. It is suggested to fit the floor tiles utilizing waterproof or water-proof glue and also grout.

    How to Install or Replace a Bathtub


    Find Your Dimensions


    The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.



    After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?


    Disconnect the Water Supply and Drain Assembly


    Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.



    Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.



    Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.


    Cut Out the Old Tub


    After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.



    Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.



    Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.


    Install the New Tub


    Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.



    Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.



    Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.



    When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.


    Secure the Tub


    After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.



    Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.



    Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.



    Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

    https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/


    How to Install a Bathtub

    I came across that entry on A Step-by-Step Guide to Installing a Bathtub while scouting around the search engines. Liked our post? Please share it. Let somebody else discover it. I praise you for your time. Come back soon.


    Course Detail

    Report this page